HG-1000S混凝土贯入阻力仪 "Times New Roman"">数显混凝土贯入阻力仪 砼贯入阻力仪 "Times New Roman"">贯入阻力仪
mso-hansi-font-family:"Times New Roman"">一、产品简介:
mso-hansi-font-family:"Times New Roman"">混凝土贯入阻力仪主要利用手动贯入阻力法来测定混凝土凝结时间。适用于各类水泥、外加剂以及不同混凝土配合比,不同气温环境下的混凝土拌合物,凝结时间的试验。外型设计轻巧美观。采用杠杆原理,将测针力直接由仪表读数,使试验方便而又准确。产品符合GB/T50080、交通部JTJ053 mso-hansi-font-family:"Times New Roman"">标准要求。
mso-hansi-font-family:"Times New Roman"">二、混凝土贯入阻力仪技术参数:
1、试料模 "Times New Roman"">上口径:Φ160mm
2、下口径:Φ150mm
3、深度:150mm
4、Z mso-hansi-font-family:"Times New Roman"">大贯入力:1000N
5、贯入深度:25mm
6、贯入速度(人工控制):2.5mm/S
7、贯入针截面积:100mm2 mso-hansi-font-family:"Times New Roman"">;50mm2 "Times New Roman"">;20mm2
8、贯入点(自选):>13points
9、测力方式:电子数显
10、Z mso-hansi-font-family:"Times New Roman"">小分度值:1N
11、示值误差:±10N
12、净重:50KG
mso-hansi-font-family:"Times New Roman"">三、操作说明:
1、将仪器安放在水平的平台上。
2、接上电源,按数显器面板上的“ mso-hansi-font-family:"Times New Roman"">电源” "Times New Roman"">键,数显窗即显示数码。请通电10 "Times New Roman"">分钟后,使数显值自动趋于“0” "Times New Roman"">。
3、选装上合适的贯入针。350N mso-hansi-font-family:"Times New Roman"">对应初凝贯入阻力(即2~3.5Mpa, "Times New Roman"">此时用100 mm2 "Times New Roman"">贯入针);1000N "Times New Roman"">对应中间贯入阻力(即3.5~20Mpa, "Times New Roman"">此时用50 mm2 "Times New Roman"">贯入针);560N "Times New Roman"">对应终凝贯入阻力(即20~28Mpa, "Times New Roman"">此时用20mm2 "Times New Roman"">贯入针)。
4、料模中装满待测试的砼试料,抹平后放于仪器底板上。
5、调整贯入深度。
mso-hansi-font-family:"Times New Roman"">混凝土贯入阻力仪一种方法是:先量出贯入针下端面与试料上平面的距离X mso-hansi-font-family:"Times New Roman"">(注意:X "Times New Roman"">不得大于5mm "Times New Roman"">,否则需适当下调贯入针),再将仪器顶部的定长螺母下平面与“ "Times New Roman"">盖”的上平面距离调整到25+Xmm mso-hansi-font-family:"Times New Roman"">,然后再拧紧螺盖,以锁住25+X "Times New Roman"">长度。
mso-hansi-font-family:"Times New Roman"">另一种方法是:压下手柄使贯入针下端面与试料上平面保持平齐,然后调整仪器上部的定长螺母,使之下平面与“ mso-hansi-font-family:"Times New Roman"">盖” "Times New Roman"">的上平面距离调到25mm "Times New Roman"">并锁住这一长度,再松开手柄。
mso-hansi-font-family:"Times New Roman"">以上两种方法的实际贯入深度均为25mm mso-hansi-font-family:"Times New Roman"">。
6、测试。首先按数显面板上的清零键b2b商务商务商务传感器的初值,即清零。再按测试键进入工作测试状态,同时数显板上金蝴蝶个灯(测试灯)亮, mso-hansi-font-family:"Times New Roman"">握住手柄向下转动,使贯入针接触试料至贯入到zui mso-hansi-font-family:"Times New Roman"">深位置(25mm "Times New Roman"">)的过程控制在10 "Times New Roman"">秒钟左右。此时数显出现峰值, "Times New Roman"">同时数显板上第二个灯(峰值灯)亮, "Times New Roman"">读出数显器的显示值,做好纪录,一次测试完成。
mso-hansi-font-family:"Times New Roman"">初凝时,使用1 cm2 "Times New Roman"">贯入针,计算公式为:P=N÷100 "Times New Roman"">(MPa);
mso-hansi-font-family:"Times New Roman"">终凝时,使用0.2 cm2 "Times New Roman"">贯入针,计算公式为:P=5 N÷100 "Times New Roman"">(MPa)。